Please Click Here if you do not see a menu frame on the left
|
||||||||||||
Before it damages your valuable MPU, remove that leaky NiCad now and use this improved off-board battery holder and your 3 AA rechargeable or non rechargeable batteries.This battery holder assembly has a 12" easily removable snap connector and hook & loop strips so you can mount it just about anywhere in the head of your machine. Several improvements have been made to this new battery holder assembly. For instance, the holder itself is a nice flat pack which will mount much easier. The 1N4004 diode was replaced with a 1N5817 diode, which has a much smaller voltage drop. The diode is mounted in the battery pack itself, so it's very neat.
Holder #1 has a diode installed so you can use it for regular Non-Chargeable AA-sized batteries. Holder #2 has a straight wire installed so you can use either NiCad or Ni-MH rechargeable batteries. The actual holder is for 4-cells but I used the first battery position to install the diode or wire. All you have to do is solder the red wire where the old battery's positive terminal went, and the black wire where the old battery's negative terminal went. The connector is polarized so once the wires are soldered in the proper place, there's no chance of connecting it wrong. Please be sure to order the proper style depending on the type of batteries you plan on using.
| $6.00 Each Battery Holder Assembly #1 For Non Chargeable Batteries |
$6.00 Each Battery Holder Assembly #2 For Rechargeable Batteries |
||
| Batteries not included, order here | |||
______________________________
4AA Battery Holder with 6" Leads
Here's a nice battery holder that holds 4 AA batteries, and can easily be made into a nice 3-AA holder for your pinball's MPU. Simply put a wire (for chargeable batteries) or a 1N5817 diode (for non-chargeable batteries) in the first battery position, then hook it up to your MPU.
| $1.50 Each 4xAA Battery Holder with leads |
Batteries not included, order here
______________________________
4AA Battery Holder with Snap
Here's a nice battery holder that holds 4 AA batteries, and can easily be made into a nice 3-AA holder for your pinball's MPU. Simply put a wire (for chargeable batteries) or a 1N5817 diode (for non-chargeable batteries) in the first battery position, then hook it up to your MPU using the 9V snap below for easy removal.
| $1.50 Each 4xAA Battery Holder |
Batteries not included, order here
______________________________
9V Battery Snap with 12" Leads
| $0.50 Each 9V Battery snap w/12" leads |
______________________________
3AA Battery Holder - Board Mounted
This is the type of battery holder used on Williams pinball boards, arcade boards and many others.
|
$5.00 Each 3xAA Battery Holder |
$21.00 Each 3xAA Battery Holder (5-Pack) |
______________________________
3AA Battery Holder - Remote mounted
Can be used anywhere, leads are approximately 5"
|
$4.00 Each 3xAA Battery Holder Remote Mounted |
$15.00 Each 3xAA Battery Holder Remote Mounted (5-Pack) |
______________________________
3AA Battery Holder - Board Mounted
Found on Data East/Sega/Stern MPU boards
This is the type of battery holder used on Data East, Sega and Stern pinball MPU boards.
Has two wire leads in the upper right croner
Data East/Sega/Stern #545-5685-00
|
$4.00 Each 3xAA Battery Holder |
$15.00 Each 3xAA Battery Holder (5-Pack) |
CR2032/CR2025 Coin Button Cell Battery Holder Socket
This battery holder can be added to many boards to use a CR2032 or CR2025 lithium battery.
|
$1.20 Each Coin Button Cell Battery Holder |
$5.00 Each Coin Button Cell Battery Holder (5-Pack) |
This is a 4-pack of AA alkaline batteries from my local warehouse club.
I've been using this brand for years and have found them to be long lasting
Typical "Best If Used By" date is 5 years out. Made in the good old USA.
| $1.50 Each 4xAA Batteries |
This really is the best solution in my opinion, using a small capacitor instead of a battery. Tests have shown this will keep your settings for over 45 days, and there's NEVER a chance of battery leakage, since this is not a battery! I secure with a dab of silicone.
| $5.00 Each 1F, 5.5 Volt Memory Capacitor |
Thank you for your business!
Big Daddy Enterprises will assume NO responsibility for any property damage and/or injury to yourself or others that may result from the use or misuse of anything you purchase from us, including services. Sending us an order implies that you understand and agree with this disclaimer.
[Home]
Big Daddy title, background art work, and Bally logo are copyright by Williams Electronics Co.
Gottlieb logos are copyright by D. Gottlieb & Company
All other content is copyright by Big Daddy Enterprises 2019 and may not be borrowed, copied,
downloaded, or reproduced in any way whatsoever without prior written consent from Big Daddy Enterprises